1.
Ahnari, A. M. A. and K. Ridgway, “An integrated modeling method to support manufacturing systems analysis and design,” Computers In Industry, 38,225-238 (1999).
陈达昌，「面向对象方法应用在集成电路构装系统信息整合研究」，硕士论文，台湾工业技术学院，(1997)。
2.
Using the Perturbation Transfer Matrix Method as well as the tested data in the laboratory, the 1st and 2nd order perturbed identification of dynamic parameters of the rotor of a boiler pump is made.
摘要利用摄动传递矩阵法，结合实验室的试验，对某电站锅炉给水泵转子的动力学参数进行了一阶和二阶摄动识别。
3.
A energy iteration method for periodic solutions to second order strongly nonlinear non-autonomous systems is suggested.
摘要给出了确定一般二阶强非线性非自治系统周期解的能量迭代方法。
4.
Based on the theory of associated and decentralized control, this paper introduces the modeling method of AC/DC power system and control law deriving, which can be realized dispersedly and guarantee the stability of the system with optimal performanc
摘要介绍了交直流电力系统关联测量分散励磁控制的建模方法和控制规律的求取，所得控制规律既可以分散实现，又能保证全局稳定且性能最优。
5.
The principle,structure and characteristic of a solid-state relay the scope of AC-DC solid-state relay are discussed.Point at AC solid-state relay,the method of reasonable selection solid-state relay,some problems that the applied circuit should be p
阐述了固态继电器的原理、结构、特点及交流直流固态继电器的适用范围,并针对交流固态继电器,提出了根据它的几个关键参数来合理选择固态继电器的方法、应用电路在设计上需要注意的一些问题以及给出了相应与计算机驳接的接口电路。
6.
Through researching the general laws of run_off formation, deducing the design formula of drainage discharge and analyzing e ach parameter of the formula, the reasonable calculation method for parameters i n the drainage design formula, is presented.
通过研究地表径流的形成规律，对排水流量设计公式的推导和计算公式中各参数意义的分析，提出滑坡排水设计计算公式中各参数的合理计算方法.
7.
Based on the linear creep superposition principle, admiting average loading age coefficient and average time-lasting coefficient, adopting creep and shrinkage calcultion in ACI code, a simplified method of creep and shrinkage analysis in reinforced c
摘要根据线性徐变的迭加原理，引入平均龄期影响系数和平均持荷影响系数，利用ACI规范中的徐变和收缩计算公式，推导了钢筋混凝土轴压构件分批加载时收缩徐变分析的简化计算方法。
8.
Material notch sensitivity test is a method which is used for certain material to measure and estimate the capability of resisting cr ack growth on the occasion of existing load stress and notch.
材料缺口敏感性试验是测定或评价某一材料在静载荷的应力条件下和有缺口的情况下，抵抗裂缝扩展能力的一种方法。
9.
The validity of the ACS method applied in the flood's enlargement is confirmed by the given example, finally, some further suggestions are presented.
通过实际洪水放大的计算，证实了该方法在洪水同频率放大优化模型中的合理性和有效性，并给出了下一步研究的方向及建议。
10.
The relationship between the clock jitter and the sampling sequence of a sine wave is studied, and a new method to measure the jitter and distribution of a clock signal with pico-second resolution is proposed using ADC sampling based on estimating me
摘要研究了时钟抖动与正弦信号的采样序列之间的关系，并在正弦信号参数估计法的基础上，提出一种利用ADC采样测量皮秒量级的时钟抖动大小和分布的新方法。
词汇听力：
小测验：选择正确的单词